產品說明Explain
公司簡介Content
品牌：MY INK 名稱：單組份自干金屬油墨編號：54165516
1、本產品是采用高級進口丙烯酸樹脂和高級顏料經過細制研磨加工組合而成，
適用范圍：各種金屬噴涂面、金屬噴漆面.金屬表面.金屬烤漆面.陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面、靜電噴漆面及烤漆面等制品的絲印及移印，不需加固化劑，不需烘烤，即可獲得優異的附著力。
2、產品特性：平光、附著力佳、流平性佳、硬度強、耐酒精、耐沖壓、抗刮傷、耐化學品。
3、稀釋劑：建議采用本公司配套專用稀釋劑開油。
4、固化劑：本產品無需加固化劑，切勿加不配套的固化劑，會影響其效果
5、油墨調配方法：攪拌時先加稀釋劑10%左右稀釋到印刷適合粘度。
6、干燥時間：恒溫表干時間自然揮發5-10分鐘，實干時間在24小時以內，48小時后達最佳性能，烤箱80℃烘烤15分鐘性能更優。冬天視地區而定。
7、使用期限：一年，過期請棄用，加了其他助劑剩余油墨不可回收。
【油墨使用注意事項】
1、試印確認符合要求后再批量生產。
2、做好被印物的表面清除油脂及雜質工作，以促進附著效果。
3、附著力、硬度、耐酸性、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測，需要完全固化后方可檢測。
4、未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。
5、絲網印刷加適量拉絲膏用本公司特慢干稀釋劑更適宜印刷工藝順暢。
【油墨性能檢測結果】
1、3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。
2、純度99%的酒精500G力在油墨表面來回擦拭100次無脫色。
【油墨使用安全規則】
1、油墨，稀釋劑使用及儲存時嚴禁煙火
2、使用時注意施工場所的通風狀況良好。
3、盡量避免皮膚直接接觸。
4、本品不慎濺入口、鼻、眼、耳內，應用大量水清洗或直接求助醫生。
5、對本品過敏者，使用前應涂覆一層皮膚扶膚膏或戴不滲透手套。
6、注意作業車間的濕度，濕度過大會影響附著力，溫度高容易堵網。
Brand: but MY product name: one from a dry metal INK Numbers: 6486694
1, the product is produced with advanced import acrylic resin and senior pigment after fine grinding system combination to, suitable scope: all kinds of metal coating surface, metal paint surface. The metal surface. Metal paint surface. Ceramic, stone, electroplating (water cut electroplating), anodic alumina surface, electrostatic spray paint surface and paint surface and so on products of screen and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion.
2, the product characteristics: good, adhesion, classification includs glass flow ping sex good, strong hardness, resistance to alcohol resistance, stamping, resistance to scratch, resistance to chemicals.
3, thinner: this company recommended supporting special thinner, open oil.
4, curing agent: this product need not add curing agent, do not add do not supporting the curing agent, it will affect its effect
5, printing ink alLOCAIION methods: first when stirred with thinner 10% dilution to printing for viscosity.
6, dry time: constant temperature dry time table natural volatilize 5-10 minutes, action in time within 24 hours, after 48 hours of the best performance, preheat the oven to 80 ℃ bake 15 minutes more optimal performance. Winter varies from area to area.
7, use period: a year, overdue please cut up, add the other additives surplus ink not recycling.
【 precautions 】 use ink
1, ShiYin confirmed again after meet the requirements of production.
2, ready to print the surface of things clear grease and impurities work to promote adhesion effect.
3 and adhesion, hardness, resistance, resistance to alcoholic acid resistance, chemical resistance character, anti-damage, wear resistance performance testing, all need to solidify rear can test.
4, without their permission, may not use the ink series with other kinds of printing ink mix and match colors.
5, screen printing and an appropriate amount of cream with the company's drawing slow dry thinners is more suitable for printing process smoothly.
【 ink performance test results 】
1, 3 M stuck in the picture has the tape's ink surface 45 degree Angle quickly pull up not to take off oil.
2 and purity, 99% alcohol 500 G force in ink surface wipe 100 times back and forth without decoloring.
【 ink use safety rules 】
1, printing ink, thinner, use and storage are prohibited during the fireworks
2, when using note the construction site of the ventilation in good condition.
3, try to avoid direct contact with the skin.
4, this product he splashed entrance, nose, eyes, ears, and application in large amounts of water cleaning or directly for help doctors.
This article 5, allergy, before the use should be coated a layer of skin and skin creams or wear infiltration gloves.
6, pay attention to the work of the workshop, humidity will influence humidity adhesion, high temperature easy plugging nets.
本產品主要用于各種金屬、玻璃、真空電鍍、水電鍍、電泳、陽極氧化鋁、電解板、鋁塑板、噴塑、噴粉、靜電噴漆面、烤漆面以及各種天花吊頂氧化板、鏡面板、覆膜板、輥涂板、尼龍加玻纖、三聚氰胺板,UV表面,木板烤漆面等等制品的絲印及移印。
2、產品特性：亮光、附著力佳、快干、耐沖壓。
3、稀釋劑：用我司B-03專用稀釋劑或783開油，用718洗網水清洗網版。
4、固化劑：單組份使用，也可選擇添加我司JS-10專用固化劑用于增加油墨附著力及物理化學抗性。
5、油墨調配方法：開罐先攪拌均勻，取所需量油墨稀釋到合適印刷粘度。如需添加固化劑，先加固化劑攪拌后靜置10分鐘，待油墨與固化劑完全交聯后再進行稀釋。
6、干燥時間：常溫干燥，表干時間5-10分鐘，實干時間在24小時以內，80℃烘烤20分鐘可快速干燥。
7、添加固化劑后的使用時限：4-6小時，過期請棄用，剩余油墨不可回收。
性能檢測
1、3M膠帶劃百格測試：100%無脫落
2、耐沖壓測試：1mm厚鋁板180°折彎無變化。
3、耐酒精測試：用脫脂棉沾濃度99%工業酒精以500G力水平來回200次無脫色。
注意事項
1、先小量試印確認符合要求后再批量生產。
2、做好承印物的表面清除油脂及雜質工作，以促進附著效果。
3、附著力、硬度、耐酸性、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測，
需要完全固化后方可檢測。
4、未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。
5、油墨，稀釋劑使用及儲存時嚴禁煙火。
6、使用時注意施工場所的通風狀況良好，盡量避免皮膚直接接觸。
7、本品不慎濺入口、鼻、眼、耳內，應用大量水清洗或直接求助醫生。
8、技術參考數見下表：
檢驗項目 檢驗結果 測試條件
油墨線度 ≤12um 刮板細度計
干膜光澤 ≥65° 60°鏡面光澤計
干燥速度 表干 25℃×5-10min 或60℃×2-3min
實干 25℃12Hr或60℃×10min
耐酒精性 無變化 500克力/cm2酒精棉200次來回
附著力 100/100 1mm×1mm×100格3M膠紙剝離
耐酸性 無變化 浸泡5%HCI×24Hr
耐堿性 無變化 浸泡5%NaOH×24Hr
耐鹽性 無變化 浸泡5%NaCI×24Hr
耐水性 無變化 浸泡20℃自來水×96Hr
耐磨性 不見底 500克/cm2負載含砂橡皮200來回
耐熱性 無變化 80℃×12Hr
The products are mainly used in screen printing and the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface and various ceiling oxide board, mirror panels, coated board, roller coated board and other products.
2, product characteristics: light, good adhesion, fast drying, stamping resistance.
3, diluent: with our B-03 special thinner or 783 open oil, washing network water cleaning screen with 718.
4, curing agent: one component use, can also choose to add our JS-10 special curing agent is used to increase the ink adhesion and physical and chemical resistance.
5, printing ink alLOCAIION methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. If you need to add curing agent, first add curing agent after mixing and set aside for 10 minutes, and curing agent for ink completely crosslinking after dilution.
6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.
7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink Unrecyclable.
[detection] performance
1, 3M tape row adhesion test: 100% without shedding
2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.
3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500G stress level and back 200 times without decolorization.
[note]
1, the first small try printing again after confirmation of compliance with the requirements of mass production.
2, do a good job in the substrate surface to remove grease and impurities, in order to promote the adhesion effect.
Detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, abrasion resistance and other properties,
Fully cured before detection.
4, without permission, may not use the series of ink and other types of ink mixing and matching.
5, ink, fireworks is strictly prohibited the use of thinner and storage.
6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.
7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing or direct help doctor.
名 稱：歐萊斯PP免處理油墨(真正免處理) 編 號：PP 適用范圍： 主要用于PP、PE、BOPP等材料上，具有高色澤、高色彩、高遮蓋力、高穩定性、耐酒精及耐磨擦之特點。 PP系列油墨 油墨特性： 擁有和德國彩麗寶一樣的顏色，主要用于PP、PE、BOPP等材料上，具有高色澤、高色彩、高遮蓋力、高穩定性、耐酒精及耐磨擦之特點。 印刷：絲印移印均可。 表干及實干時間：表干時間自然揮發5-10分鐘；實干時間在24小時以內。 稀釋及清洗：SV3慢干開油水、UVK1（移印開油水）同時可使用718洗網水清洗。 測試方法（完全干燥后）： 1、3m膠紙粘在畫有百格的油墨表面，45度角迅速拉起不脫油; 2、純度99%的工業酒精，一千克砝碼用棉布包住在油墨表面，以水平力來回拉200次無脫色; 3、 耐磨：橡皮擦500g力水平來回擦500次。 使用方法： 1、使用前應充分攪拌，用后隨時封閉； 2、攪拌時加開油水10-15%，稀釋到印刷粘度； 3、網板塞網時可用洗網水清洗； 4、不得與其它類型油墨混合使用。 注意事項： 1、塑膠材料的外觀相似，但可能會是不同的材料，客戶需試印確定其符合要求后，再批量印刷； 2、在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可; 3、環境溫度過高，將會影響油墨原有質量； 4、根據氣候變化，請遠離火源，陰暗環境下存放。
898995850
