ble shooting

8.1 沖孔系統故障排除 Punching system trouble shooting

   8.1.1   故障現象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機器不動 Symptom: The machine does not move

           產生原因：電源沒有接通或者保護開關觸發異常。

Cause: The power supply is not turned on or the protection switch is triggered
  排除方法：查看電源開關是否已經接通，保護開關有無異常， 配電箱內空氣開關是否斷開。

Remedy: Check whether the power switch is switched on, whether the protection switch is abnormal or not, and the air switch in the distribution box is disconnected
8.1.2異?，F(xiàn)象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機毛邊大

Abnormal phenomenon: big hair
  產生原因：紙張?zhí)?，沖針嚴重磨損

Cause: The paper is too thick and the punch is severely worn
  排除方法：正常運行紙張厚度建議在1-6mm之內；如果是沖針磨損嚴重請更換。Remedy: normal operation of the paper thickness is recommended within 1-6mm; if the pins wear, please replace.

8.2 全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機器手送料系統的故障排除 The feed belt system trouble shooting

   8.2.1 故障現象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機器不動Symptom: The machine does not move

         產生原因：電源沒有接通或者光電開關觸發異常。Cause: The power supply is not turned on or the photoelectric switch triggers an abnormality
         排除方法：查看電源開關是否已經接通，光電開關有無異常。Remedy: Check whether the power switch is turned on, the photoelectric switch is abnormal.

   8.2.2  異?，F(xiàn)象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機械手抓取和送料位置不對             Abnormal phenomenon: the robot grab and feeding POSTTTION is wrong

   產生原因：皮帶拉長松弛或者是皮帶固定塊1不牢靠。        Cause: The belt is stretched or the belt is fixed

   排除方法：將皮帶張緊到合適的松緊度，調整好機械手的位置鎖緊皮帶固定塊。Remedy: Tighten the belt to the appropriate tightness, adjust the POSTTTION of the robot to lock the belt fixed block.