2.1 臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機上料裝置的調整 Adjust the feed belt

  該工位可根據產品的寬窄來調節輸送料道的寬度，參考（圖九）松開護罩1的固定螺絲123，然后根據產品的需要調整料道的寬窄。The POSTTTION of the station can be adjusted according to the width of the product to adjust the width of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the width of the material according to the needs of the material.

收料裝置的調整(參考圖三) Adjust the receive belt (Picture 3)

  該工位主要是配合主機完成收料工作，可根據主機的裝訂速度自動調整線體的每次位移. The station is mainly with the host to complete the receipt work, according to the host's binding speed automatically adjust the line of each displacement.

3. 臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機推刀調試 Test push knife

   根據產品大小的需要，可通過調節推刀組的固定螺絲的安裝位置來調節T的寬度（見圖十）Depending on the size of the product, the width of the T can be adjusted by adjusting the mounting POSTTTION of the setscrews' fixing screws (Picture 10)

4.臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機孔位自動校正系統的調整 Adjust the corrective system

  此工位主要是通過整形針來實現孔位校正的，根據產品的需要可調整整形針間的間距和角度。。This POSTTTION is mainly through the pins to achieve hole correction, according to the needs of the product can adjust the space between the needle and angle.

5.臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機自動繞線穿線系統的調整 Adjust the inserting system

機器出廠前已裝有調試好的一套模具。當機器需要更換模具時，可按照以下步驟進行。The machine is shipped with a good set of molds. When the machine needs to replace the mold, follow the steps below.
5.1  臺歷 掛歷 筆記本全自動YO單/雙線圈裝訂機穿線 Inserting the wire

將線穿入進線組件，經過過線輪24.1，潤滑盒25，過線輪24.2,計數輪26（經過計數輪時將線繞計數輪一圈），過線輪24.3,再經過鐵線整直板(如圖一)，之后在芯棒上.