菏澤grc構件-濟南浩博建材
GRC構件主要成分和工藝

GRC構件的主要成分與生產工藝是怎樣的?
The main component of the production process GRC member of what?
GRC構件的成分與工藝。持久耐用,隔熱隔音的。
ComPOSTTTION and Process GRC member. Durable, insulated soundproof.
建筑物連接結構為實心塊狀砌體結構，GRC構件砌體強度大于Mu7.5，砂漿強度大于M5，砌體厚度大于等于370㎜采用置換塊，置換塊應采用C20級以上膨脹細石混凝土灌注，厚度240㎜,商標轉讓，高度和寬度不小于240㎜.錨栓應安裝在置換塊中心位置,模型制作，不符合上述要求之一時，應對建筑物連接結構進行結構驗算或加固，采用透墻對穿螺栓加錨板固定。
Building block connecting structure is solid masonry structure, GRC members masonry strength greater than Mu7.5, mortar strength greater than M5, masonry thickness greater than or equal 370㎜ use replacement block replacement block should be above the level of expansion C20 fine aggregate concrete pouring when the thickness 240㎜, trademark transfer, the height and width of not less than 240㎜. anchors should be installed in the center of the replacement block LOCAIION, model making, does not meet one of these requirements, the connection structure to deal with the building or strengthening structural checking, through the use of wall plus anchor plate bolts for wear fixed.
當GRC構件較大時應預留錨板，錨板應采用強度不低于Q235級鋼，錨板的厚度應不小于構件配筋直徑的0.6倍，錨板鍍鋅層的鍍鋅含量不小于350g/㎡;錨栓或鋼筋穿孔中心至錨板邊緣的距離D不應小于2d或20 mm，穿孔與鋼筋之間的最大間隙不應大于2mm.。鋼筋與錨板延穿孔周邊雙面滿焊。
When the GRC members should set aside a larger anchor plate, anchor plate should not be less than the strength of Q235 grade steel, the thickness of the anchor plate shall be not less than 0.6 times the diameter of the reinforcement member, the content of the anchor plate galvanized zinc coating is not less than 350g / m; anchor or anchor plate steel perforated center to the edge of the distance D is not less than 2d or 20 mm, the maximum gap between the perforated steel and should not be greater than 2mm .. Perforated steel and cast anchor plate surrounding sided fully welded.
GRC構件以無水硫鋁酸鈣和硅酸二鈣為主要成分的熟料加入適量石膏磨細制成的早強水硬性膠凝材料.稱為硫鋁酸鹽快硬水泥.性能為:比表面>380m2/Kg初凝〈25min、終凝〈3h，強度為425、525、625。GRC制品的強度除取決于水泥強度外，還取決于單件表面尺寸及填料比，配置不同的筋骨支撐結構(如竹筋鋼筋等)所決定的，廠家也會根據建筑需要進行科學的骨架配置。
GRC member anhydrous sulfur calcium aluminate and calcium silicate as the main component of clinker is added early strength cement matrix made of an appropriate amount of gypsum ground called Sulphoaluminate rapid hardening cement performance: ratio surface> 380m2 / Kg initial setting <25min, the final setting <3h, strength of 425,525,625. In addition to the strength of GRC products depends on the strength of cement, it also depends on the size of a single surface and filler ratio, configure different muscles support structures (such as bamboo reinforcement bars, etc.) of the decision, the manufacturers will need to be configured according to scientific skeleton construction .
GRC構件——預混工藝
GRC members - premixed Process
預混合過程是切碎的玻璃纖維與水泥砂漿基體共同混合，形成均勻的玻璃纖維水泥混合物，然后通過鑄造或注塑的方法制成的產品。根據不同的成型方法，預混工藝可分為預混混凝土技術和預混射流技術。預拌混凝土和預制混凝土產品技術類似，在澆注過程中，往往輔以振動過程。
Pre-mixing process is chopped glass fiber and cement mortar matrix mixed together to form a uniform glass fiber cement mixture, and then the product is made by casting or injection molding method. Depending on the method of molding, premix process can be divided premixed concrete technology and premixed jet technology. Similar ready-mixed concrete and precast concrete product technology, in the casting process, often supplemented by vibration process.